In Priming Mode, Nothing turns on Automatically*.*Note: On the VS/GS Model, the Circ Pump will be on, and on some EL/GL Models, a continuous filtration pump** turns on automatically. Also, on the VS/GS Models, Freeze Protect Mode overrides Priming Mode, and All pumps will be on in Freeze Protect Mode.The purpose of Priming Mode is to allow the user to manually verify that the pumps are primed (which typically requires observing the output of each pump separately, which is generally not possible in normal operation). Priming Mode lasts 4 minutes, but you can exit it earlier by pressing any Temp button.**Note: The term "circ pump" refers to a low-speed-only pump that is used for heating and possibly also for filtering. If a continuously running low-speed-only pump is only used for filtering (not for heating), that is not called a circ pump, but instead may be referred to as a "continuous filtration pump".You should verify priming on all pumps the first time you fill the spa with water, as well as each time you refill the spa with water (after having previously drained it). You can skip Priming Mode if you're restarting the spa for some other reason (without the water having been drained since the last time the spa functioned properly).If you have a Circ Pump, do this first (EL version):- Push the Jets 1 button once. This turns on pump 1, and also turns on the circ pump.- Verify that both pump 1 and the circ pump are running and that water is flowing out of both their outlets into the spa. If they're not, or you're not sure that both are (because you can't tell whether you have two separate flows at different rates or just one flow), momentarily turn both pumps off and on (by pressing Jets 1 multiple times) to help the pumps to prime. Do not do this more than 5 times. Do not let the pumps run for a total of more than 2 minutes if they haven't primed by then. Observe the panel display as you do this. If you haven't successfully primed both pumps by the time the Priming Mode display ( Pr or PRIMING MODE depending on panel) ends, turn off the spa IMMEDIATELY.If after two minutes you cannot verify that water from the circ pump is flowing because the water motion from pump 1 obscures it, press the Jets 1 button again until all pumps turn off. Then press Temp once to exit Priming Mode. Unless the water is very cold, only the circ pump will start for one minute. If you do not see water flowing from the circ pump outlet, IMMEDIATELY turn off power to the spa (as an attempt at heating will occur within a minute of the circ pump attempting to start). (It's 2 minutes on the VS/GS, and 2 minutes on EL/GL versions earlier than 21.) You cannot cycle the circ pump once you've exited Priming Mode, so go back to the previous step to try to prime it.
The spa, when powered up at the customer's installation, will begin a GFCI Test countdown that can be factory set from 1 - 7 days. The GFCI can also be tripped manually via the Edit Menu interface titled gFC.Button press instructions for initiating a GFCI trip manually can be found HERE.If the spa is not installed with a GFCI and the system fails to sense a trip, the system will not allow the spa to operate unless a GFCI is properly installed.If the spa water reaches a temperature of 110 degrees F, a "Stuck Relay Timer" will begin to count from 0 hours, while the system monitors water temperature over time.If the spa goes through the typical Overheat Errors and continues on to exhibit specific temperature-rise-over-time requirements, the system will assume a pump relay is stuck ON, and has no ability to shut it off. In this condition, an attempt is made to trip the GFCI, which would shut off all power to the spa.
Aqua-air V100 Manual
The Ready-in-Rest mode is a sub-function of Rest mode. This mode activates if the spa is in Rest mode and Pump 1 is activated manually. The spa then thinks that people are using it, and heats the water to the desired temperature. Pump 1 then functions on low speed until the water reaches that temperature or for one hour. After an hour, the control system automatically goes back to Rest mode. It is also possible to set the spa to the mode you want with the adjustment menu. 2ff7e9595c
Kommentit